Pioneer Xdj Rx2 Software

Posted on  by 



Thanks a lot for the mapping I managed to get the sound through the mixer by using external sound card and 2 input for each channel most of the functions works except the FX could you please share more information about how to make the setup correctly. This guide is a how-to for streaming using a 3rd party software such as OBS, and many of these instructions may also be applied to other software. The instructions provided herein are based around a XDJ-RX2, and may be different for other XDJ units. Please check the XDJ or DDJ sections of the Knowledge Base for additional tutorials. Step 1 - Update.




MIDI MODE


On the XDJ-RX2 :
  1. Press the MIDI button at the left side of the Display
  2. Press the LOAD 1 button at the right side of the Display
  3. Press the LOAD 2 button at the right side of the Display

The unit is now ready to operate.

MIDI Operation


The unit should be visible in the CONTROLLERS tab of Config as 2 separate units (one for the main unit and an additional one for the Display) and the “factory default” available/selected from the Mappings drop-down list for both units. The factory default Mapping offers the functions described in this Manual, however those can be adjusted to your needs via VDJ Script actions.
Find more details at http://www.virtualdj.com/wiki/VDJ8script.html

AUDIO Setup


The unit has a pre-defined Audio setup and a special button in the AUDIO tab of Config to provide that.
Alternative audio configurations can be applied See Advanced Setup
For further software settings please refer to the User Guides of VirtualDJ 8.
http://www.virtualdj.com/manuals/virtualdj8/index.html
Refer to the manual of the unit for further features-settings. at... https://www.pioneerdj.com/en/support/documents/xdj-rx2/
Layout

  1. PAD MODE. Press any of the 4 available Pad mode buttons to set the Pads to Hotcues, Loop, Loop Roll and Beatjump mode.
    Hold SHIFT and then press any of the 4 available Pad mode buttons to set the Pads to Saved Loops, Sampler, Slicer and Keycue mode.
  2. PADS. The 8 Pads offer different functionality depending on the selected mode.

The Parameters of each mode can be adjusted from the VirtualDJ GUI (Pads section)
Read further details about Pads in the VirtualDJ 8 manual

HOTCUES




LOOP

Pioneer Xdj Rx2 Software


LOOP ROLL

Pioneer Xdj Rx2 Software Review




Beatjump mode




Saved Loop mode




SAMPLER



Dj Xdj Rx2


Use the Parameter arrow-buttons from the GUI of VirtualDJ (Pads section) to select the Sampler Bank (previous/next).

SLICER




Hold SHIFT and then use the Pads to repeat the memorized Slices (the Slices played/repeated last time)
Use the Parameter arrow-buttons from the GUI of VirtualDJ (Pads section) to adjust the length of the Loop applied to the slice. or adjust the step of the Slices

Key-Cue mode


Hold SHIFT down and then press the BEAT JUMP mode button to set the PADs to KeyCue mode (button will be lit yellow) and automatically load the KeyCue Pads page in VirtualDJ GUI


In this mode, the Pads trigger a selected Hotcue point (or the Temporary Cue if none selected or not available) at a selected Key semitone (from -7 to +7).
8 different pages/banks are offered with various semitone values to use and a 0 value (reset key to tis original value) is always offered in all pages.
Hold SHIFT and then select a Hotcue

Pioneer Xdj Rx2 Software Manual

for the Key pads to trigger. Each time a Pad is pressed, the track will jump to that Hotcue point and will also alter the Key of the track to the value designated by it assigned value.

Xdj Rx2 Flight Case

Use the Parameter arrow-buttons on the GUI of VirtualDJ (Pads section) to adjust the Key of the track without trigger a Hotcue.
or select a different

Pioneer Xdj Rx2 Used

page/bank

Pioneer Xdj Rx2 Software Free

with different key semitone values.
Microphone



Coments are closed
Anydesk For Raspberry Rekordbox Iphone